Klipsch RF-7 III Floorstanding Speaker Pair with RC-64 III Center Channel Speaker

KSh1,050,000.00

Specifications

RF-7 III Floorstanding Speaker

  • Frequency response: 32 – 25kHz +/-3dB
  • Power handling: 250W/1000W peak
  • Sensitivity: 100dB @ 2.83V/1M
  • Nominal impedance: 8 ohms compatible
  • High frequency horn: 8.5″ square 90° x 90° Tractrix Horn
  • High frequency drivers: 1.75″ titanium diaphragm compression driver
  • Crossover frequency: 1,300Hz & 1,400Hz
  • Low frequency drivers: Two 10″ Cerametallic cone woofers
  • Inputs: Dual binding posts/bi-wire/bi-amp
  • Enclosure type: Dual-chambered, bass-reflex via dual rear-firing Tractrix ports
  • Dimensions (H x W x D): 49″ x 13.875″ x 17.875″
  • Weight: 97 lbs.

 

RC-64 III Center Channel Speaker

  • Frequency response: 57 – 24kHz +/-3dB
  • Power handling: 200W/800W peak
  • Sensitivity: 99dB @ 2.83V/1M
  • Nominal impedance: 8 ohms compatible
  • High frequency horn: 6.25″ square 90° x 90° Tractrix Horn
  • High frequency drivers: 1.75″ titanium diaphragm compression driver
  • Crossover frequency: 1,000Hz & 1,400Hz
  • Low frequency drivers: Quad 6.5″ Cerametallic cone woofers
  • Inputs: Dual binding posts/bi-wire/bi-amp
  • Enclosure type: Sealed
  • Dimensions (H x W x D): 8″ x 35.8″ x 15″
  • Weight: 55 lbs.
 

Description

RF-7 III Floorstanding Speaker
The Klipsch RF-7 III speaker is a testament to the quality that Klipsch demands from each and every one of its audio products. Remember great sound? Klipsch does, too. The RF-7 III enclosure is made in the USA, by proud craftsmen in Hope, Arkansas.
  • New 1 3/4″ Titanium Diaphragm Compression Driver – The compression driver features a new phase plug design to improve phase coherency at the throat of the horn, resulting in improved sound pressure linearity at high frequencies.
  • 90° x 90° Tractrix Horn  – The redesigned Tractrix horn utilizes a circular horn throat paired to a square horn mouth to further improve high-frequency response and extension, while enhancing imaging and dynamics. The compressed molded rubber construction adds high-frequency damping to reduce harshness and improve detail. This creates the cleanest, most natural sound possible.
  • Spun Copper Cerametallic Woofers – Cerametallic woofers represent the pinnacle of Klipsch driver design, maintaining exceptional rigidity, and lightweight construction, for minimal cone breakup and distortion. When paired with the Tractrix horn-loaded compression drive, it provides speaker efficiency highest in its class.
  • New Tractrix Port – Utilizing Tractrix geometry, the new RF-7 III ports allow for the most efficient air transfer from the cabinet – for the cleanest, most powerful low frequency response on the market.
  • Dual-Chambered Enclosure Design – The new bifurcated enclosure allows each 10″ driver and port to work independently from the other. This improves the linearity of both drive systems, and minimizes standing wave problems inside the cabinet that can cause frequency anomalies in the sensitivity midrange frequencies.
  • Cast Frame Woofer Design – Each 10″ woofer features a heavy-duty cast aluminum frame for resonant-free operation. In addition, each woofer incorporates a dual shorting-ring magnet structure design to eliminate modulation of the magnetic flux resulting in improved linearity of cone movement.
  • Furniture Grade Wood Veneers – RF-7 III enclosures all utilize furniture grade wood veneers.
RC-64 III Center Channel Speaker
The Klipsch RC-64 III speaker is a testament to the quality that Klipsch demands from each and every one of its audio products. Remember great sound? Klipsch does, too. The RC-64III enclosure is made in the USA, by proud craftsmen in Hope, Arkansas.

 

  • New 1 3/4″ Titanium Diaphragm Compression Driver – The compression driver features a new phase plug design to improve phase coherency at the throat of the horn, resulting in improved sound pressure linearity at high frequencies.
  • 90° x 90° Tractrix Horn – The redesigned Tractrix horn utilizes a circular horn throat paired to a square horn mouth to further improve high-frequency response and extension, while enhancing imaging and dynamics. The compressed molded rubber construction adds high-frequency damping to reduce harshness and improve detail. This creates the cleanest, most natural sound possible.
  • Spun Copper Cerametallic Woofers – Cerametallic woofers represent the pinnacle of Klipsch driver design, maintaining exceptional rigidity, and lightweight construction, for minimal cone breakup and distortion. When paired with the Tractrix horn-loaded compression drive, it provides speaker efficiency highest in its class.
  • Cast Frame Woofer Design – Each 6.5″ woofer features a heavy-duty cast aluminum frame for resonant-free operation.
  • 2 1/2-Way Network Crossover Design – The sophisticated design of the RC-64 III network attenuates the outer woofers’ output at higher frequencies to minimize horizontal interference off-axis to the loudspeaker. This maintains a wide and even sound distribution – ensuring each listener hears the center channel information exactly as intended.
  • Furniture Grade Wood Veneers – RC-64 III enclosures all utilize furniture grade wood veneers.

Reviews

There are no reviews yet.

Be the first to review “Klipsch RF-7 III Floorstanding Speaker Pair with RC-64 III Center Channel Speaker”

Your email address will not be published. Required fields are marked *